x1000 onboard network opensource driver in progress: new version

	Bottom Previous Topic Next Topic
Register To Post

« 1 ... 4 5 6 (7)

Petrol

Re: x1000 onboard network opensource driver in progress: new version

Posted on: Yesterday 17:35 #121

Just popping in

@kas1e

Quote:

You mean dock not working ? And that only with pa6t driver, but work with realtek drivers ?

It's as if the processor is overloaded; the graphics in the various dockies (CPUDock, NetDock, ...) do not refresh constantly and struggle to function.
I need to check with the RTL driver.
Edit: Ok I've got the same behavior with the RTL driver.

Quote:

you mean local network and driver monitor whole network traffic like arp and co ? And in this situation dock works ? Cant it be that you mess with docks settings ?

As soon as I start a download on my Mac, I also see the activity in the Dockie. I can also see the amount of data received or sent increasing, not only in the dockie, but also in Ranger for example, in the Network/General tab you can see this by refreshing the page.
I don't see That with RTL driver.

I'm using default settings for the dockie.

In case it could help, this what I've got on the serial


[pa6t_eth] Init: pa6t_eth.device 1.1 (23.03.2026) (c) 2026 kas1e

[pa6t_eth] FindDevices: L2C ECAM=0xE0008000 (id=0xA0091959)

[pa6t_eth] FindDevices: MC0 ECAM=0xE0020000 (id=0xA00A1959)

[pa6t_eth] FindDevices: MC1 ECAM=0xE0028000 (id=0xA00A1959)

[pa6t_eth] DiagInit: phys=0x17CC0000 virt=0x5A810000 (2048 entries, 131104 bytes)

[pa6t_eth] *** AFTER CRASH: CFE> d 0x17CC0000 ***

[pa6t_eth] Init: ready. MAC 02:00:E0:0A:30:00

[pa6t_eth] Init: copy path = RoadShow internal (S2_CopyToBuff)

[pa6t_eth] S2_SANA2HOOK: supported methods: 0x800B0001 0x800B0002 0x800B0008(DMACopyToBuff32) 0x800B0009(DMACopyFromBuff32)

[pa6t_eth] S2_SANA2HOOK: DMA copy: to=1 from=1

[pa6t_eth] PostRxBuffers: DMA Memory+BusMaster enabled (was 0x0000)

Kind regards,

Edited by Petrol on 2026/3/25 21:59:19

TearsOfMe

Re: x1000 onboard network opensource driver in progress: new version

Posted on: Yesterday 20:26 #122

Just popping in

I ran VNC with shows Twitch for about two hours and didn't have any problems. Downloads worked fine, too. Uploads seem to be slow, but maybe only Problem here?

Quote from page 1:
Find out that on my x1000, when i connect router to the onboard NIC and then power on machine, then the leds both on router and on the NIC are green. All fine. Then, if i do reset by reset button on tower, they go to offline, and never come up even after OS4 loads up again. So , to make link again to work, i had to do exactly power off / power on.

I guess I still have that here.

Edited by TearsOfMe on 2026/3/25 22:25:17

Register To Post	« 1 ... 4 5 6 (7)
	Top Previous Topic Next Topic

Currently Active Users Viewing This Thread: 1 ( 0 members and 1 Anonymous Users )