@Spirantho

I have fun, believe it. ;)

Hiho, i'm so happy. :)
With the new driver-release my CatweaselMK4 will work on the Pegasos2 under OS4. :D
Thanks ian, great work. ;)

@all

is here anyone who has running a Catweasel MK4 in a PegasosII under OS4.1.2 ?

@Spirantho

I have 2 communication devices:

- Vendor 0xE159

- Vendor 0x1106

Is one of them the Catweasel ?

@Spirantho

Nothing will work.

I post you my Installation that i have now.

- CW installed in the 3rd PCI-Port
- 1 PC-Floppy installed and connected to the 2nd connector (behind the twist)
- installed last archive of your driverpackage

now tell me please what i have to do. :(

i have changed floppies and cabels .... and cabels and floppies ....

@spirantho

ok, same problems all the time.

what i have done:

- installed catweasel hardware @ slot 2 on the Pegasos II board
- installed floppycable from PegII-Board to the CW-Hardware as described
- installed a floppycable with 4 ports from the CW-Hardware
- connected first (or second) 3,5" port to a pc-floppydrive (some drives tested)
- installed your driver-archive in the prefered places
- doubleclicked th0 or th1

result:

volume in drive x has readerrors on disc-block 0


where is the problem ?

me ? :)

@MH2

nice work. ;)

is the installer multilanguage ? (english, german, ...)


if not i can help with german translation, if needed.

ok here my sashimi.out:

Opening catweasel.device with flags 1
Checking controller unit for controller 6659E9E0
unit number 0
flags 1
unit address 0
Creating unit for number 2
Allocated. Now initing 652F3000
Allocating drive geometry.Inited.
Init unit: 2
unit adr: 652F3000
LibOpenLight success.
open unit no 0
IO units now set to 652F3000
Received IORequest 9
unit hex no 652F3000
Waiting for completion.
Found message.
Execute!!!!
ETD_CLEAR = 8005
Command 9
TD_MOTOR
CMD_MOTOR: Motor is 0
Turning motor off.
Motor is now 0
motor length set to 0
motor was 0
IO CMD DONE, return code 0
Done request.
Received IORequest 14
unit hex no 652F3000
Waiting for completion.
Done request.
Received IORequest F
unit hex no 652F3000
Waiting for completion.
Found message.
Execute!!!!
ETD_CLEAR = 8005
Command 14
TD_ADDCHANGEINT
Found message.
Execute!!!!
ETD_CLEAR = 8005
Command F
TD_PROTSTATUS
IO CMD DONE, return code 0
Done request.
Received IORequest E
unit hex no 652F3000
Waiting for completion.
Found message.
Execute!!!!
ETD_CLEAR = 8005
Command E
TD_CHANGESTATE
Seek to 0
Current is 0
Never found track 0.
Error 30
Offset 0
Len 0
Block 0
IO CMD DONE, return code 1E
Done request.
Received IORequest 16
unit hex no 652F3000
Waiting for completion.
Found message.
Execute!!!!
ETD_CLEAR = 8005
Command 16
TD_GETGEOMETRY
IO CMD DONE, return code 0
Done request.
Received IORequest F
unit hex no 652F3000
Waiting for completion.
Found message.
Execute!!!!
ETD_CLEAR = 8005
Command F
TD_PROTSTATUS
IO CMD DONE, return code 0
Done request.
Received IORequest 9
unit hex no 652F3000
Waiting for completion.
Found message.
Execute!!!!
ETD_CLEAR = 8005
Command 9
TD_MOTOR
CMD_MOTOR: Motor is 0
Requesting turning motor on.
Turning motor on now...catweasel_set_motor 1
Done.
Motor is now 1
motor length set to 1
motor was 0
IO CMD DONE, return code 0
Done request.
Received IORequest 2
unit hex no 652F3000
Waiting for completion.
Found message.
Execute!!!!
ETD_CLEAR = 8005
Command 2
CMD_READ
index 0length 200
Reading Track 0 Side 0 Sector 0
Seek to 0
Current is 0
Never found track 0.
Exiting read_track with error 30
Done read/write
Error code was 30
Actual bytes 200
Error 1E
Error 30
Offset 0
Len 512
Block 0
IO CMD DONE, return code 1E
Done request.
Received IORequest 9
unit hex no 652F3000
Waiting for completion.
Found message.
Execute!!!!
ETD_CLEAR = 8005
Command 9
TD_MOTOR
CMD_MOTOR: Motor is 1
Turning motor off.
Motor is now 0
motor length set to 0
motor was 1
IO CMD DONE, return code 0
Done request.
catweasel_set_motor 0

thats my way for the output:

- run sashimi
- doubleclick TH0
- close the upcomming requester
- start a shell an type "break 6 all"
- post the sashimi.out here ;)

in catweasel prefs i have 3,5" Double Sided 80 track saved.

@Spirantho

now i have tried some pc-drives, some amiga-drives (dd/hd), amiga-disks and pc-disks.
Every time the same Failure. :(

@Spirantho

Heyho, i run Catweasel Prefs an if i press "SAVE" an Console-window pops up:

"touch: unknown command"

sashimi i will test next time

@Spirantho

What i mean is the Hardware. ;)
I have installed PC-Floppys on the Catweasel, no special Amiga-Floppys. ;)

Hiho from Germany ;)

i have also problems with Catweasel in my PegasosII under OS4.1.2.
The driver won't run.
Floppies are from PC. (changed 5 or 6)
If the ML starts (automatic or manual) a Message pops up:

"Disk in drive TD0 has readerrors in disk-block 0"

Same thing on TH0 (or 1)


The driver is version 1.6 and the Mountlists are also from here.
If the Message pops up, the WB is blocked.

Any reasons ?