@broadblues

You are right, when using the " international font ",causes crasch to close the program.

For the rest, seems to work well

Greetings

Hello!
I downloaded the blender, and is a marvel.
But when I try to change the language, nothing happens
how i can change the language on blender

Greetings

@Troels


Here in my region (Galicia - Northwest Spain) we usually have dinner with seafood (crayfish, prawns, scallops, barnacles, etc, etc) and after a vegetable stew with potatoes and beans, cooked pork and pork sausages too, and drinking red wine .

Merry Christmas to all and happy new year 2010, be good and Santa Claus will bring the AmigaOS 4.1 update

best regards.

@jackepc

Hi jackepc, the world is small, I'm glad to see you here. welcome friend.

Greetings.

Hola jackepc, el mundo es peque?o, me alegro de verte por aqui, bienvenido amigo.

SalU2.

@freddix

It is a good news, I am very happy
that your Sam440ep works again.
Good luck, greetings.
Lisardo

Hello

I have Lightwave 3D 5.0 for Amiga, bought to NewTek USA directly, with dongle in the parallel port, and he works very well in my Amiga 1200, but I cannot prove it in my Sam440ep, because the Sam doesn't have parallel port to plug the dongle.
Does somebody know if exists a PCI card with parallel ports that it can be plugged in the slot PCI of the Sam?

A greeting,
Lisardo.

@freddix


It is possible that the reset button doesn't work correctly, or make contact continually, of being this way when start up the Sam anything it would not be seen in the screen of the monitor, however the hard disk and the DVD would have activity.

Greetings,
Lisardo

@Samurai_Crow

Hi Samurai_Crow

Now I will download the archive.
Thank you for your answer .

greetings,
Lisardo R L

Hello to all!

Does somebody know where to download the documentation of the SdlBasic?
Commands, functions, sentences, etc, etc.

Documentation to print, non documentation on line.

regards,
Lisardo.

@ ice2642

Ok, I have installed the card and I have made the following tests with the program CubeBM.
The screen configured with the driver RADEON:

resolution : 1680x1050 32bits
-------------------------------------------------------------
Test without the card:
Output Motherboard DVI connector

13842 frames drawin in 17.1 seconds
1103 fps (0.906 milliseconds per frame)
817 fps (1.223 milliseconds per frame with swap)

--------------------------------------------------------------
Test with the card pluged in :
Output Motherboard DVI connector

14406 frames drawin in 18.2 seconds
1100 fps (0.908 milliseconds per frame)
802 fps (1.246 milliseconds per frame with swap)
-------------------------------------------------------------
The screen configured with the driver PCIgraphics :

Output Saphire Radeon 9250 DVI connector


When I attempt the test with the connected monitor to the card (driver PCIgraphics) then the system crash
--------------------------------------------------------------------

I believe that there is not difference, the system the two GPUs it doesn't use in team.



A greeting.

@All

Hello to all!

Finally I have bought a SAPHIRE RADEON 9250 PCI 128MB 64-BIT DDR, 40 Eurs, but cheap that the MAC edition (120 Eurs).
The card works well, I have two monitors one for the card and another for the motherboard, I have installed the DualGraphicCardSetup, and only I can use a monitor at the same time, that is to say if I configure the resolution with the driver RADEON, the image goes to the monitor that this connected one to the motherboard of the Sam, and if I configure the screen with the driver PCI the image goes to the monitor that this connected one to the graphic card.
Another thing that it happens it is that with the graphic card installed in the slot PCI and when pulling up the AmigaOS 4.1 only works one USB connector, the top rear, ? it is a bug ?.
I have installed the last updates of Hyperion.

A greeting to all

@ZeroG

Thank you friend.

This is the connector of the Sam440ep motherboard, this if I connect the MIC from the front panel to the pines 5 ,9,6 and 10 ?, and the Earphone at the pines 11 and 13 or 15 and 17 ?, I ignore if it is as well as they are connected, this it is my question.

1 ? 3.3 V
2 ? 5 V
3 ? SPDIFI
4 ? SPDIFO
5 ? MIC1
6 ? LINE_IN_L
7 ? JD0
8 ? JD2
9 ? MIC2
10 ? LINE_IN_R
11 ? SURR_L
12 ? PCIM_OUT
13 ? SURR_R
14 ? PCIM_IN
15 ? AUX_L
16 ? CEN_OUT
17 ? AUX_R
18 ? LFE_OUT
19 ? FMIC
20 ? VREFOUT
21 ? GND
22 ? GND

Thank you.

I have my Sam440ep in a SuperCase MI 008, in their front part it has 2 connectors USB, 1 MIC in and 1 EarPhone out.
Does somebody know as connecting the MIC in and the Earphone out to the Sam 440ep motherboard?
The front panel has two connectors USB, 1 AUDIO HD connector(10 pin) and 1 connector AC'97 (10 pin).
Thank you to all.
Lisardo.

@MamePPCA1

I cannot make sure to 100%, I don't have an A1, but according to the images and the comments of the web that I recommend you up, I believe that you won't have problems in mounting it in your A1, interrogative also tells it to you, the salespersons that tell you that it is not good to mount in a CPU they don't know that they are speaking ( no se enteran de nada ), they ignore the measures of the PPC CPU of the A1, they don't know that the anchorages of the fan coincide with those of the A1, most of salespersons of PC?s don't know anything about what sells ( solo saben que precio tiene y que es para PC ), me after seeing the images, and of reading what comments interrogative, I believe that it is the fan that you need.

A greeting

@MamePPCA1

He looks at this image, it is an A1 with that fan, it is the Zalman V900-CU



Go to the web-----> http://metacomco.com/hardware/
and look the fantastic A1.

Greetings

@mr2

It is this way, that it is the trick, I ignored that pngalpha.l.main should be copied to the directory LIBS: together with pngalpha.library, I am new with the AmigaOS 4.1.

@salass00


Thank you my friend salass00 !

I have copied the pngalpha.l.main file in LIBS together with the pngalpha.library, and now the programs work perfectly.
Thank you and a greeting.
Lisardo.

Hello to all

I have some problems when I try to open SkinnableClock and also with PictureWidget.

The pngalpha.library is in LIBS

Does somebody know because the programs that I try to open up don't work?
that I can make so that they work?

Thank you and a greeting.

@MamePPCA1

Well, here you have a spanish WEB where you can buy the Zalman VF 900 fan that recommends you " interrogative ", I hope it is you of help.
A greeting.

http://www.alternate.es/html/productDetails.html?artno=JZZ%2341