Login
Username:

Password:

Remember me



Lost Password?

Register now!

Sections

Who's Online
90 user(s) are online (78 user(s) are browsing Forums)

Members: 0
Guests: 90

more...

Headlines

Report message:*
 

Re: X5000 No Longer Booting OS4!

Subject: Re: X5000 No Longer Booting OS4!
by AcillClassics on 2020/12/26 18:04:17

This is serial output:

2 USB Device(s) found
SATA0 (3 Gbps)
U-Boot 2014.04 (Oct 17 2016 - 08:22:22)
CE at device
CPU0: P5020, Version: 2.0, (0x82200020)
Core: e5500, Version: 1.2, (0x80240012)
Clock Configuration:
CPU0:1995 MHz, CPU1:1995 MHz,
CCB:798 MHz,
DDR:665 MHz (1330 MT/s data rate) (Asynchronous), LBC:49.875 MHz
FMAN1: 498.750 MHz
QMAN: 399 MHz
PME: 399 MHz
L1: D-cache 32 KiB enabled
I-cache 32 KiB enabled
Reset Configuration Word (RCW):-ST Prod.: DVDRAM GH24NSC0 Rev: LI00
00000000: 0c540000 00000000 1e1e0000 00000000
00000010: 44808c00 ff002000 68000000 45000000
00000020: 00000000 00000000 00000000 0003000f
00000030: a0000000 00000000 00000000 00000000
Board: CYRUS
36-bit Addressing
I2C: ready
SPI: ready
DRAM: Initializing....using SPD
DDR: failed to read SPD from address 81
Detected UDIMM VS2GB1333D3
There is no rank on CS0 for controller 0.
Not enough bank(chip-select) for CS0+CS1 on controller 0, interleaving disabled!
Not enough bank(chip-select) for CS0+CS1 on controller 1, interleaving disabled!
Not all DIMMs are identical. Memory controller interleaving disabled.
2 GiB (DDR3, 64-bit, CL=9, ECC off)

Local Bus Controller Registers
BR0 0xE0001001 OR0 0xFFF00010
BR1 0xE1001001 OR1 0xFFF00010
BR2 0x00000000 OR2 0x00000000
BR3 0x00000000 OR3 0x00000000
BR4 0x00000000 OR4 0x00000000
BR5 0x00000000 OR5 0x00000000
BR6 0x00000000 OR6 0x00000000
BR7 0x00000000 OR7 0x00000000
LBCR 0x40000000 LCRR 0x80010004
L2: 512 KiB enabled
Corenet Platform Cache: 2 MiB enabled
SERDES: bank 2 disabled
MMC: FSL_SDHC: 0
EEPROM: NXID v0
PCIe1: Root Complex, x4 gen2, regs @ 0xfe200000
01:00.0 - 1002:683d - Display controller
01:00.1 - 1002:aab0 - Multimedia device
PCIe1: Bus 00 - 01
PCIe2: Root Complex, x4 gen2, regs @ 0xfe201000
03:00.0 - 111d:8092 - Bridge device
04:01.0 - 111d:8092 - Bridge device
05:00.0 - 12d8:e111 - Bridge device
04:02.0 - 111d:8092 - Bridge device
07:00.0 - 10ec:8168 - Network controller
04:03.0 - 111d:8092 - Bridge device
04:08.0 - 111d:8092 - Bridge device
04:10.0 - 111d:8092 - Bridge device
PCIe2: Bus 02 - 0a
PCIe3: disabled
PCIe4: disabled
Looking for VGA
PINS: 0xfc000808
videoboot: Booting PCI video card bus 1, function 0, device 0
Begin BIOS POST
End BIOS POST
Setting VESA Mode
Found required VESA mode
About to set mode 279
About to get mode
Got mode 49431 (0xc117)
OK
XSize = 1024 YSize = 768 Base =0xe0000000
mmio_base = 0x80000000
bgx = 0xad55ad55 fgx = 0x0
In: serial
Out: serial
Err: serial
ID: NXID v0
SN: 116330024
UID: 4429431001910050e4d4a080a0800000
Errata: ÿÿÿÿÿBGÿ
Build date: 2015/06/11 14:42:47
CRC: 3d2fd346
SCSI: scanning bus for devices...
Found 0 device(s).
Net: Initializing Fman

MMC read: dev # 0, block # 1130, count 128 ...
Fman1: Uploading microcode version 106.1.0
Tuning PHY @ 3
Tuning PHY @ 7
FM1@DTSEC4 [PRIME], FM1@DTSEC5

MMC read: dev # 0, block # 1280, count 512 ... 512 blocks read: OK

MMC read: dev # 0, block # 65536, count 131072 ... 131072 blocks read: OK
USB0: USB EHCI 1.00
scanning bus 0 for devices... 4 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... 2 USB Device(s) found
SATA0 (3 Gbps)
SATA1 (1.5 Gbps)
CE at device
scanning bus for devices...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Not ready...
Device 0: (1:0) Vendor: HL-DT-ST Prod.: DVDRAM GH24NSC0 Rev: LI00
Type: Removable CD ROM
Capacity: not available
Found 1 device(s).
## Starting application at 0x00200000 ...


Loading finished [########################################] 100 %
About to call loader entry at 0x7BD02020

Powered by XOOPS 2.0 © 2001-2016 The XOOPS Project