Login
Username:

Password:

Remember me



Lost Password?

Register now!

Sections

Who's Online
139 user(s) are online (80 user(s) are browsing Forums)

Members: 0
Guests: 139

more...

Headlines

 
  Register To Post  

(1) 2 »
[solved] X1000 broken or GFX card problem
Just can't stay away
Just can't stay away


See User information
Hi,
as my X1000/R7-250X doesn't display something et screen anymore, is someone could advice me ?


At boot, the gfx card fan begin to rotate but soon stop.
No output on my screen (no signal detected)

In the debug log, I see :
No suitable VGA device found in the system.

and from PuTTY, I'm able to start to boot but either in 4.1.6 or FE :

Picasso96 cannot configure your graphics board!
Either your board is not supported or there's a configuration problem.
Did you install PCIGraphics.kmod?


Is somebody encountered this problem ? GFX card broken and/or power problem and/or dead X1000 ?

Thanks


Full debug serial output :

▒[HELO][DRAM]SDRAM: ECC off, Non-ECC DIMM used on channel 0.
SDRAM: ECC off, Non-ECC DIMM used on channel 1.
[RELO][L1CF][GOLO][GOT ][ZBSS][INIT][MAIN][KMEM][EXCP][CONS][CIOK][AREN][PCIH][PCIB][PCIS][DEVI]

CFE version PAS-2.0.30 for NEMO (64bit,MP,BE,PPC)
Build Date: Fri Jun 8 16:04:49 CEST 2012 (hfrieden@jumpgate)
Copyright (C) 2000,2001,2002,2003,2004,2005 Broadcom Corporation.
Portions Copyright (C) 2005-2008 PA Semi, Inc.
Portions Copyright (C) 2010 Hyperion Entertainment CVBA

Initializing Arena.
Initializing PCI. []
PCI bus 0 slot 16/0: PCIe: port 0 could not be activated
PCI bus 0 slot 17/1: PCIe: port 5 could not be activated
PCI bus 0 slot 17/2: PCIe: port 6 could not be activated
PCI bus 0 slot 17/3: PCIe: port 7 could not be activated
SB600 revision A21 in Intel P4 mode
PCI bus 5 slot 18/0: ATI Technologies product 0x4380 (IDE mass storage, interface 0x8f)
PCI bus 5 slot 19/0: ATI Technologies product 0x4387 (USB serial bus, interface 0x10)
PCI bus 5 slot 19/1: ATI Technologies product 0x4388 (USB serial bus, interface 0x10)
PCI bus 5 slot 19/2: ATI Technologies product 0x4389 (USB serial bus, interface 0x10)
PCI bus 5 slot 19/3: ATI Technologies product 0x438a (USB serial bus, interface 0x10)
PCI bus 5 slot 19/4: ATI Technologies product 0x438b (USB serial bus, interface 0x10)
PCI bus 5 slot 19/5: ATI Technologies product 0x4386 (USB serial bus, interface 0x20)
PCI bus 5 slot 20/0: ATI Technologies product 0x4385 (SMBus serial bus, rev 0x14)
PCI bus 5 slot 20/1: ATI Technologies product 0x438c (IDE mass storage, interface 0x83)
PCI bus 5 slot 20/2: ATI Technologies product 0x4383 (multimedia subclass 0x03)
PCI bus 5 slot 20/3: ATI Technologies product 0x438d (ISA bridge)
PCI bus 5 slot 20/4: ATI Technologies product 0x4384 (PCI bridge)
PCI bus 6 slot 5/0: Realtek Semiconductor 8139 10/100 Ethernet (ethernet network, rev 0x10)
Initializing Devices.
GPIOLV10 Jumper: Not fitted (default VGA console)
GPIOLV11 Jumper: Not fitted (default ?)
PHY: mb, addr 0x00, vendor 03f1 device 15 (1)
No suitable VGA device found in the system.
cf0: Card inserted (3V)
IDE unit 0: Disk, "ST2000DM001-1ER164", Capacity:1863GB (lba48)
ATAPI unit 1: Optical Drive, "TSSTcorp CDDVDW SH-222BB"
PCIIDE: 2 controllers found
Initializing USB.
PCI bus 5 slot 19/5: EHCI USB controller found at 80209800
USB bus 0 device 1: vendor 0000 product 0000 class 09: USB Hub
PCI bus 5 slot 19/0: OHCI USB controller found at 80207000
USB bus 1 device 1: vendor 0000 product 0000 class 09: USB Hub
PCI bus 5 slot 19/1: OHCI USB controller found at 80206000
USB bus 2 device 1: vendor 0000 product 0000 class 09: USB Hub
PCI bus 5 slot 19/2: OHCI USB controller found at 80208000
USB bus 3 device 1: vendor 0000 product 0000 class 09: USB Hub
PCI bus 5 slot 19/3: OHCI USB controller found at 80204000
USB bus 4 device 1: vendor 0000 product 0000 class 09: USB Hub
PCI bus 5 slot 19/4: OHCI USB controller found at 80205000
USB bus 5 device 1: vendor 0000 product 0000 class 09: USB Hub
CPU type 0x900102: 500MHz
Total memory: 0x100000000 bytes (4096MB)

Total memory used by CFE: 0x7FD1DF60 - 0x80000000 (3023008)
Initialized Data: 0x7FDD8420 - 0x7FDF8B00 (132832)
BSS Area: 0x7FDF8B00 - 0x7FDFF000 (25856)
Local Heap: 0x7FDFF000 - 0x7FFFF000 (2097152)
Stack Area: 0x7FFFF000 - 0x80000000 (4096)
Text (code) segment: 0x7FD1DF60 - 0x7FDCBE60 (712448)
Relocation Factor: I:7FE1DF60 - D:7FE1DF60
[ENVI]
[OFW ][UI ]Requested state A4 (1800MHz)
port 0:1/1 released (full speed)
USB: New device connected to bus 1 hub 1 port 1 (full speed)
USB bus 1 device 2: vendor 0F39 product 1083 class 03: Human-Interface Device
USBHID: Keyboard Configured.
0: AmigaOS
1: AmigaOS CD Boot
2: Ubuntu 16.04 - Kernel 4.5
3: Ubuntu 16.04 - Kernel 4.1
Press 'F' to enter the firmware prompt
Loader:elf Filesys:amigafs Dev:ide0.0 File:amigaboot.of Options:(null)
Loading: 0x0000000000200000/50812 0x000000000021C67C/76 Entry at 0x0000000000200034
Starting program at 0x0000000000200034
[RUN!]
AmigaOS 4.x OpenFirmware Bootloader V1.0



Please choose a configuration to boot (Default choice is green):
1: AmigaOS4.1.6 (Volume DH0)
2: AmigaOS4.1.6_Debug (Volume DH0)
3: AmigaOS_4.1_Final_Edition (Volume DH6)
4: AmigaOS_4.1_Final_Edition_Debug (Volume DH6)

[RETURN] Boot default [SPACE] Stop Countdown
[CTRL-U] Move default up [CTRL-D] Move Default Down
[1234] Boot appropriate config
> 1
Trying to boot configuration AmigaOS4.1.6
port 0:1/5 enabled (high speed)################-----------------------] 43 %
USB bus 0 device 2: vendor 05E3 product 0608 class 09: USB Hub
USB: New device connected to bus 0 hub 2 port 3 (low speed)
USB bus 0 device 3: vendor 10D5 product 000D class 03: Human-Interface Device
USBHID: Unknown Configured.
*** delete async 0:2/0 [#############################-----------] 72 %
ehci_ept_delete 0:2/1 (i) has active qTDs
*** delete async 0:3/0
rtg.library AltiVec/VMX enabled######################################] 100 %
rtg.library PA6T optimizations enabled
Picasso96 cannot configure your graphics board!
Either your board is not supported or there's a configuration problem.
Did you install PCIGraphics.kmod?




Trying to boot configuration AmigaOS_4.1_Final_Edition
gfx AltiVec/VMX enabled [########################################] 100 %
gfx PA6T optimizations enabled
graphics.library cannot configure your graphics board!
Either your board is not supported or there's a configuration problem.
Did you install PCIGraphics.kmod?




Edited by zzd10h on 2016/4/11 17:38:09
Go to top
Re: X1000 broken or GFX card problem
Just can't stay away
Just can't stay away


See User information
reverted back to my old HD6670 gfx card solved the problem.
=> R7-250X dead !


Go to top
Re: X1000 broken or GFX card problem
Home away from home
Home away from home


See User information
@zzd10h

Is the R7-250X dead? Or, was the external power connector dislodged (or just plain not connected)?

I have occasionally forgotten to plug in the external power with my Radeon HD 7770, and the machine's behaviour is similar to what you describe.

Hans

http://hdrlab.org.nz/ - Amiga OS 4 projects, programming articles and more.
https://keasigmadelta.com/ - more of my work
Go to top
Re: X1000 broken or GFX card problem
Home away from home
Home away from home


See User information
@zzd10h

thankfully it's "only" the video card ..

Go to top
Re: X1000 broken or GFX card problem
Just can't stay away
Just can't stay away


See User information
@Hans
Yes, I checked the external GFX card connector, no problem

@Samir
yes ;)

Go to top
Re: X1000 broken or GFX card problem
Quite a regular
Quite a regular


See User information
Thats not good news, sorry to hear that.

amigakit.com - the Amiga store
Links: www.amigakit.com | New Products | Enhancer Software
Go to top
Re: X1000 broken or GFX card problem
Quite a regular
Quite a regular


See User information
@zzd10h

Luckely it wasn't your X1000...

AmigaOS 4.1 FE Update 2 on Sam440ep-flex, 800Mhz, 1GB RAM, Radeon 9250 Resized Image
A1200/040, 2+4MB, external 3.5''HDD / A1200 (spare) / A500+ (sold) / C128 (sold)
http://m4rko.com/AMIGA
Go to top
Re: X1000 broken or GFX card problem
Just can't stay away
Just can't stay away


See User information
Im happy to hear it wasnt the x1000 :)

Go to top
Re: X1000 broken or GFX card problem
Quite a regular
Quite a regular


See User information
Guillaume,
gfx board dont die alone expecially if new... i suggest you in any way to take a look to the psu.

X5000/40 16GB
RasperryPi 1-2-3-4-(5)
A500 Mini.
Go to top
Re: X1000 broken or GFX card problem
Just can't stay away
Just can't stay away


See User information
Wonderful,

Matthew/AmigaKit gently sent me a new R7-250X.

Plugged and it works !

A big public thank you, Matthew, it is very kind

Go to top
Re: X1000 broken or GFX card problem
Just can't stay away
Just can't stay away


See User information
@tlosm

Quote:
gfx board dont die alone expecially if new... i suggest you in any way to take a look to the psu.


Of course they do, as anything else ! When will you stop telling nonsense on Amiga forums ?

--
AmigaONE X1000 and Radeon RX 560
Go to top
Re: X1000 broken or GFX card problem
Quite a regular
Quite a regular


See User information
@zzd10h

Congratz!

AmigaOS 4.1 FE Update 2 on Sam440ep-flex, 800Mhz, 1GB RAM, Radeon 9250 Resized Image
A1200/040, 2+4MB, external 3.5''HDD / A1200 (spare) / A500+ (sold) / C128 (sold)
http://m4rko.com/AMIGA
Go to top
Re: X1000 broken or GFX card problem
Quite a regular
Quite a regular


See User information
@K-L
i had 100 or more gfx board in my life and never die alone...
only ancient old die because capacitors and some because the fans.
Probably guillaume board was factory defected, i think is the only reason for the board die expecially in an amiga system where the gfx never use all it power

X5000/40 16GB
RasperryPi 1-2-3-4-(5)
A500 Mini.
Go to top
Re: X1000 broken or GFX card problem
Not too shy to talk
Not too shy to talk


See User information
@tlosm

especially Graphics cards die these days. That is because a RoHS.

Componets are made lead free, so solderings are not what they used to be.

Luckily it is possible to fix these kinds of problems with kicthen owen. Turn it on, set temperature to 190-195c. Separate everything what you can and put it owen for 20-30min.

If problem is because a lead free solderings, it stars to work again after that.


Edited by utri007 on 2016/4/12 21:53:38
Go to top
Re: X1000 broken or GFX card problem
Quite a regular
Quite a regular


See User information
@utri007

thanks fot the explanations,
didnt know , i was thinking this issue was effecting only the console (xbox 360)

X5000/40 16GB
RasperryPi 1-2-3-4-(5)
A500 Mini.
Go to top
Re: X1000 broken or GFX card problem
Just can't stay away
Just can't stay away


See User information
@utri007

Quote:
Turn it on, set temperature to 90-95c. Separate everything what you can and put it owen for 20-30min.

And... do you usually have your gfx card with roast potatoes, or just some vegetables? :)

The Rear Window blog

AmigaOne X5000 @ 2GHz / 4GB RAM / Radeon RX 560 / ESI Juli@ / AmigaOS 4.1 Final Edition
SAM440ep-flex @ 667MHz / 1GB RAM / Radeon 9250 / AmigaOS 4.1 Final Edition
Go to top
Re: [solved] X1000 broken or GFX card problem
Not too shy to talk
Not too shy to talk


See User information
None of those. It smells bad, so no food for own same time.


Edited by utri007 on 2016/4/12 21:42:08
Go to top
Re: [solved] X1000 broken or GFX card problem
Just can't stay away
Just can't stay away


See User information
Can i put my x1000 in the owen :')

Go to top
Re: [solved] X1000 broken or GFX card problem
Just can't stay away
Just can't stay away


See User information
@Kicko

Sure.

But to be safe, don't turn it on (the oven, I mean ).

Best regards,

Niels

Go to top
Re: [solved] X1000 broken or GFX card problem
Not too shy to talk
Not too shy to talk


See User information

Go to top

  Register To Post
(1) 2 »

 




Currently Active Users Viewing This Thread: 1 ( 0 members and 1 Anonymous Users )




Powered by XOOPS 2.0 © 2001-2023 The XOOPS Project