Login
Username:

Password:

Remember me



Lost Password?

Register now!

Sections

Who's Online
34 user(s) are online (20 user(s) are browsing Forums)

Members: 0
Guests: 34

more...

Headlines

 
  Register To Post  

OS4.1 Install /Boot
Just popping in
Just popping in


See User information
I have booted from my os4.1 install cd and it loads the kickstart then goes to the insterting disk what have i meesed up as i get the same screen when i boot from the harddrive, is this a setenv parameter?
HELP!!!!

Go to top
Re: OS4.1 Install /Boot
Just can't stay away
Just can't stay away


See User information
@caver99

Enter the early startup menu. Do you see your disk in the possible boot sources?

Philippe 'Elwood' FERRUCCI
Sam460ex 1.10 Ghz
http://elwoodb.free.fr
Go to top
Re: OS4.1 Install /Boot
Just popping in
Just popping in


See User information
@caver99

Yes i see both hard drives and both dvd roms it boot the kickstart off of the main boot drive then i get the kickstart window.

Go to top
Re: OS4.1 Install /Boot
Just popping in
Just popping in


See User information
@caver99

i have just found the early boot screen and no dh0 or dh1 are not there, have i messed up a u-boot setting?

Go to top
Re: OS4.1 Install /Boot
Supreme Council
Supreme Council


See User information
@caver99

It sounds like you need to set the boot source in the Amiga Multiboot settings of UBoot.

This is accessible from the preferences menu when the system starts up.

Simon

Go to top
Re: OS4.1 Install /Boot
Quite a regular
Quite a regular


See User information
Yes, this happened to me when I first installed my new SAM with the accompanying 4.1

My experience with an AmigaOne was good assistance here.

I changed the booting value in 2 of the menus I believe but 1 is probably the most important.

also, once your workbench appears please enter a shell and type:

nvsetvar sii3114ide_xfer G00G

then reset immediately

This will prep your devices attached.

If you like and you know where your drives are you can set it to GOOG

which on the SAM would be set best udma mode for unit 0 and best udma mode for unit 3

Harddrive and DVDRW respectively

mine is set to GGOG since I have two harddrives attached.

Hope that doesn't confuse you

p.s. sorry if you don't own a SAM but are using something else... sii3114ide in the above command will have to be replaced with your equvialent

~Yes I am a Kiwi, No, I did not appear as an extra in 'Lord of the Rings'~
1x AmigaOne X5000 2.0GHz 2gM RadeonR9280X AOS4.x
3x AmigaOne X1000 1.8GHz 2gM RadeonHD7970 AOS4.x
Go to top
Re: OS4.1 Install /Boot
Just can't stay away
Just can't stay away


See User information
@Slayer

> GOOG

Note that these are "zero" not "O".

Philippe 'Elwood' FERRUCCI
Sam460ex 1.10 Ghz
http://elwoodb.free.fr
Go to top
Re: OS4.1 Install /Boot
Just can't stay away
Just can't stay away


See User information
@caver99

Stupid question, but have you installed the slb on your hd when installing amiga os on your hard drive ?.. Without it your system cannot boot up..

Go to top
Re: OS4.1 Install /Boot
Just popping in
Just popping in


See User information
@caver99

Yes i have had the system fully working then i started to mess to try and get the system to boot from cd rom now my hdd wont boot, even if the slb was not present on my hdd why wont the cd boot past the kickstart screen??
I am comming close to pulling my battery out and flushing the uboot and trieing from scratch.
I can redirect the uboot out put to serial but whast good will that do, can i connect that to my pc and capture the output or something?

Go to top
Re: OS4.1 Install /Boot
Just popping in
Just popping in


See User information
@caver99

ok, i have just removed my battery and now it will boot inti the install thats great, what settings will i need to enter in the set env to boot from harddrive?

Go to top
Re: OS4.1 Install /Boot
Just popping in
Just popping in


See User information
@caver99

Please take a look at the installation guide I have done.

You can download it HERE

There's some hints at the end of this giude

For example, in order to force U-Boot to use harddisk or optical type of peripheral, you can set a specific variable :
sete sii3114ide_conf 1002

'1' is used for harddisk, '2' for optical devices and '0' for nothing.

Also, please not that harrdisk should be connected to the J20 connector of the motherboard and the optical drive shoubd be connected to the J23 connector.

Hope it will help ;)

Laurent aka Faranheit

ZORAWSKI Laurent
Your Amigaventurer
Tel : (+33) 971 290 616
GSM : (+33) 6 98 74 13 25
Mail : faranheit@wanadoo.fr
MSN : laurentzorawski57@hotmail.com
Skype : faranheit57
ICQ : 81617715
Go to top
Re: OS4.1 Install /Boot
Quite a regular
Quite a regular


See User information
@Elwood

read the

nvsetvar sii3114ide_xfer G00G

again, they do have 0 in it apposed to O

only in my string does it have a O

:p

~Yes I am a Kiwi, No, I did not appear as an extra in 'Lord of the Rings'~
1x AmigaOne X5000 2.0GHz 2gM RadeonR9280X AOS4.x
3x AmigaOne X1000 1.8GHz 2gM RadeonHD7970 AOS4.x
Go to top

  Register To Post

 




Currently Active Users Viewing This Thread: 1 ( 0 members and 1 Anonymous Users )




Powered by XOOPS 2.0 © 2001-2016 The XOOPS Project