I originally had 1x2Gb (Corsair) in my X-5000 and after reading the recommandation from Kas1e regarding his latest ports I replace it with 2x1Gb of Kingston which were laying around and after running Ragemem, I am getting the expected number for write32/64 (around 1'500)

@328gts

for Atomic Bomberman session you have to log to discord server, which as you might guess, does not work under Odyssey...
so it is a no go for me !

same here can not connect, altough I could a few weeks back
noticed that some played on an unknown server recently.

AOS4 iso for X-5000 is done by Hyperion which do not have the SFS rights anymore, bought by A-EON so you get SFS2 when you purchase the Enhancer Pack from A-EON, but you can not boot from a SFS2 partition on a X-5000, at least not at first.

You always need a NGFS partition to boot the system initially ("cold boot")... same goes for FFS2 BTW

little update :
formatted the USB stick either as FFS2 or NGFS and copied over the content of the X-5000 pre release CD.

in both cases I got the following error :
invalid partition type "DOS\7" (expect "U-Boot")
invalid partition type "NGF\0" (expect "U-Boot")

what does this means ?? do I have to install the SLB in the RDB of the USB stick ?? where can I get it ?? it is NOT present in L: as it used to be for AmigaOne system !

what a mess and no support regarding this little question...

countdown or delay ?

type nvgetvar in your shell to get your U-Boot parameters.

here is what I have :

amigaboot_quiet=N
amigabootmenu_animate=0
baudrate=115200
bdev=sda3
bootargs=root=/dev/sda2 mem=3500M console=ttyS0,115200 console=tty0
bootargs_live=root=/dev/ramdisk boot=casper mem=3500M ro --
bootargs_live_debug=root=/dev/ramdisk boot=casper mem=3500M ro break debug
bootcmd=setenv bootargs root=/dev/$bdev rw console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr - $fdtaddr
bootdelay=10
bootdvd=scsi reset ; load scsi 0 2000000 boot_dvd ; bootm 2000000
bootfile=uImage
consoledev=ttyS0
eth1addr=00:50:C2:20:DA:CC
ethact=FM1@DTSEC4
ethaddr=00:50:C2:20:DA:CB
ethernetboot=echo Running Ethernet Boot
ethprime=FM1@DTSEC4
fdtaddr=c00000
fman_ucode=7fe73380
harddiskboot=echo Running Hard Disk Boot
hwconfig=fsl_ddr:ctlr_intlv=cacheline,bank_intlv=cs0_cs1;usb1:dr_mode=host,phy_type=utmi;usb2:dr_mode=host,phy_type=utmi
linuxboot=echo Running Linux
liveusb=usb start ; setenv bootargs_live_debug ; ext2load usb 1:1 2000000 boot_dvd ; bootm 2000000
loadaddr=1000000
loadbmps=mmc read 0x10005000 0x500 0x200; mmc read 0x20000000 0x10000 0x20000
massboot=echo Running Mass Storage Boot
mos=bootmorphos
netdev=eth0
nfsboot=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr - $fdtaddr
opticalboot=echo Running Optical Boot
preboot=run loadbmps;bmp d 0x20000000;ami
ramboot=setenv bootargs root=/dev/ram rw console=$consoledev,$baudrate $othbootargs;tftp $ramdiskaddr $ramdiskfile;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr $ramdiskaddr $fdtaddr
ramdiskaddr=2000000
ramdiskfile=ramdisk.uboot
rootpath=/opt/nfsroot
scsidevs=1
stdin=usbkbd,serial
stdout=serial,vga
uboot=u-boot.bin
ubootaddr=0xFFF80000

@levellord

still no go : RawDisk does not let me choose 0 as start cylinders (min is 2048)...

I tried rawrite32 on win7 (Kas1e said in another thread it is the best tool for such thing) where the start is at 0 but the USB key is not recognized under AOS4...

any help/suggestion welcome.

@levellord

there is none, thats why I was asking for it a few posts above...

I tried the Khayoz suggestion (thanks man !) but I forgot to set the start cylinders at 0 (is 2048 by default)
will repeat and report back if it works !

@LiveForIt

well I am not talking about MOS here, I dont have it installed !

I just want to copy the content of the X-5000 pre release CD to a USB stick and asking which FS should I format the USB stick with so that I can boot from it at startup. I tried FAT and it was not recognized.

knowing that on X-5000 you can only boot for a NGFS partition (at least you need the kickstart drawer in a NGFS partition), I am wondering if the USB stick has to be formatted as NGFS or something else.

got again an error on one partition having SFS2 (BlockID error) !

I could make a backup and reformat the partition by using the X-5000 prerelease CD as boot but I would like to use a USB stick to make it a little bit faster.

Since I got a second hand beta system, I dont have the Flash Drive USB stick customers got when purchasing a full X-5000 system therefore I am asking those what is the filesystem used for this FlashDrive ? is it NGFS, FAT, NTFS, FFS ??

FolderSync2 from Chris Handley comes to my mind !
http://aminet.net/package/util/cli/FolderSync2

thank you for these nice artworks and hard work ! sadly your links can not be accessed through Odyssey...

@walkero

thank you for the (updated) scripts !
interestingly enough is that sites like github and itch.io are displayed much better under IBrowse 2.5 than under Odyssey !

BTW am I the only one where the installer failed to install the whole package ? it just report a "unable to open the tool "Scummvm_install""

Snoopy does not show anything...

nice progress though !

AFAIK on AOS4 you need the other engine (residual) to run it (although it got merged into Scummvm some time ago)
http://os4depot.net/?function=showfil ... /adventure/residualvm.lha

maybe Raziel can comment...

you might find some answers in the FPSE compatibility DB : https://www.amidog.se/fpsedb/

@ktadd

I have this line : RX SYS:s/Arexx/YT.rexx %l html odyssey silent
the only difference is html and autoplay

Grunch might be a good starting point : http://www.geit.de/eng_grunch.html

ah and welcome (back?) to/on Amiga Land !

in theory everything you purchased should show up after you logged in under "My purchases" and if there is an update, you will get a sign.