Login
Username:

Password:

Remember me



Lost Password?

Register now!

Sections

Who's Online
108 user(s) are online (63 user(s) are browsing Forums)

Members: 0
Guests: 108

more...

Headlines

 
  Register To Post  

AmigaOne G3-SE safe overclock @667MHz
Just popping in
Just popping in


See User information
HI,

I was wondering if anyone with the G3-SE have overclocked it. And if so, how far and with what voltages ? I understand that at least the G4s have been fried before, so what is the safe area in terms of voltages ?

I have only tried to increase the multiplier up to 5 (5x133.33 = 666.66MHz), from the standard 4.5 (600MHz). This without increasing any voltage (1.59V) so it should be completely safe. However, at some points it can then crash (for instance in the middle of Quake 3), so I would like to increase the voltage one tick up (1.64V), and see if it is stable then.

Thanks!


Edited by monomango on 2019/3/22 10:22:08
Go to top
Re: AmigaOne G3-SE safe overclock @667MHz
Just popping in
Just popping in


See User information
@monomango

I didn't know you could overclock the SE, pretty cool!


Quake 3 suddenly crashing unfortunately seems to normal,
I've tried numerous source ports and all would randomly crash on my stock 800mhz 7451 and it still crashes on my 1066mhz 7457,
with a lovely continuous buzz sound coming out of the speakers :)


Btw, the smoke trail of the rocket launcher really kills performance on my 9250,
I recommand to go to the console and type

cg_noProjectileTrail 0

to disable it, makes it so much faster and clearer too!



r_ext_compressed_textures 1

Also gains some FPS, but the textures will look very low res.


Here's a list of all Q3 console commands

Go to top
Re: AmigaOne G3-SE safe overclock @667MHz
Just popping in
Just popping in


See User information
@Helloworld

Yeah, the DIP switches seems to be exactly the same.

I've also had Q3 crash/freeze before due to the infamous DMA issue affecting USB/Network on those boards..
I have given up on using the USB even with a PCI card as it leads to instabilities (might still be fine to use if onboard LAN is unplugged though and EHCI disabled in Kicklayout). However, when I do have a USB card plugged in the PCI PATA and SATA cards can freely be used with UDMA6 enabled on both, no issues. If I disable onboard USB and don't install the PCI USB card, then the Sii0680 and Sii3114 boards can't be used in UDMA6 mode, possibly not in any UDMA mode, freeze at boot.

With onboard USB disabled it *might* have completely stable ethernet with the onboard 3com controller, as long as (assumption) the PCI USB is not used. Peculiar system indeed. With this config I also had Q3 running for a long time playing over LAN with no issues at all at any time.

However, using the RTL8169 PCI Ethernet instead makes it completely solid. So now my system will only use PCI based Ethernet going forward. The last stability issue seems to be solved (DMA freeze from using onboard Ethernet).
Regarding Quake 3, my FPS increased by about 10% after increasing the CPU clock speed by about the same amount (600MHz -> 667MHz). Quake 3 really seems CPU bound on these systems.


Thanks for the performance advices there, I will check it out ! :)


EDIT:
I just now increased the VCC_Core voltage from 1.59V (the default for 750CXe it seems) to 1.64V. It made it stable (so far) and Q3 stopped crashing like it did, sometimes while launching before.

My systems FSB is set to 133MHz, and original multiplier was set to x4.5. This was raised to x5.0 for 666.66MHz (~667MHz, 666MHz is shown in Ranger).

The settings are as follows, found in previous sources using the internet way-back machine from archive.org and the A1 XE manual :

Multiplier settings (switches close to the CPU):
x2 on off on on
x2.5 on off off on
x3 off on on on
x3.5 off off off on
x4 off on off on
x4.5 on off off off (Default for my CPU, 600MHz @ 133MHz FSB)
x5 off on off off (667MHz @ 133MHz FSB)
x5.5 off on on off
x6 off off on off
x6.5 on off on off
x7 on on off on
x7.5 on on on off
x8 off off on on

For increasing the voltage; J1 and J17 was set from
1.59V: On Off On Off Short (Default for my CPU @ 600MHz)
to
1.64V: Off On On Off Short (Should be enough for 667MHz)
i.e. rising the voltage one level up.

The next two levels (which I dare not test) are :
1.69V: On On On Off Short
1.74V: Off Off Off On Short

It seems 1.59V and 1.64V is a very low setting for the 750CXe. In IBM's data sheet 1.80V is listed as its normal core voltage.. Therefor, I suspect it is quite overclocking friendly, as long as the temperatur is monitored.

EDIT 2 :
I have tried with voltages all the way up to 1.84V, which still is within the safe range according to the data sheet. However, 733MHz cannot be reached, freezes at boot. I keep it at 667MHz and 1.64V, which indeed seems to be the sweet-spot.


Edited by monomango on 2019/3/17 17:41:35
Edited by monomango on 2019/3/17 17:45:13
Edited by monomango on 2019/3/19 15:26:02
Edited by monomango on 2019/3/19 15:28:18
Edited by monomango on 2019/3/19 15:32:15
Edited by monomango on 2019/3/19 15:36:01
Edited by monomango on 2019/3/20 1:55:30
Edited by monomango on 2019/3/20 2:02:21
Edited by monomango on 2019/3/20 2:03:37
Edited by monomango on 2019/3/20 2:08:33
Edited by monomango on 2019/3/20 2:10:57
Edited by monomango on 2019/3/20 2:14:49
Edited by monomango on 2019/3/21 5:13:41
Edited by monomango on 2019/3/21 5:14:43
Edited by monomango on 2019/3/21 5:15:44
Edited by monomango on 2019/3/21 7:11:01
Edited by monomango on 2019/3/22 9:05:40
Edited by monomango on 2019/3/22 9:37:10
Edited by monomango on 2019/3/22 10:02:05
Edited by monomango on 2019/3/22 10:02:54
Edited by monomango on 2019/3/22 10:18:11
AmigaOne G3-SE : G3@667MHz, Radeon 9200 AGP 256MB, 2GB Reg 133MHz RAM, RTL8169 gigabit Ethernet, NEC USB 2.0, Sii0680/Sii3114, PS/2 keyboard and mouse
AmigaOne X5000 : P5040, Radeon RX580, 16GB Reg RAM, ESI Juli@
Both: AmigaOS 4.1 FE Update 2, Linux
Go to top
Re: AmigaOne G3-SE safe overclock @667MHz
Not too shy to talk
Not too shy to talk


See User information
@monomango

Hi!
I overclocked my old A1SE to 667 MHz just after buying it and used it for about 7 years without big problems I used an ATA133 Sil card and onboard ethernet.
I only modified the moltiplcator without touching the core voltage.

Simone"Tuxedo"Monsignori, Perugia, ITALY.
Go to top
Re: AmigaOne G3-SE safe overclock @667MHz
Just popping in
Just popping in


See User information
@Tuxedo

Hi

Thanks for the insights. Did you end up selling it? Or, if you still have it, would it be possible to check your voltage setting ?

Interesting thing, mine was set to 1.59V and 600MHz from when I got it. However, with memtester it seems to give some errors .. then raising the voltage to 1.64 and all errors gone.. 667MHz speed. Maybe it was too low voltage affecting some memory operations, a bit weird.

I have been running memtester for over 40 hours, and its all good now with no errors for any of the tests. :)

AmigaOne G3-SE : G3@667MHz, Radeon 9200 AGP 256MB, 2GB Reg 133MHz RAM, RTL8169 gigabit Ethernet, NEC USB 2.0, Sii0680/Sii3114, PS/2 keyboard and mouse
AmigaOne X5000 : P5040, Radeon RX580, 16GB Reg RAM, ESI Juli@
Both: AmigaOS 4.1 FE Update 2, Linux
Go to top

  Register To Post

 




Currently Active Users Viewing This Thread: 1 ( 0 members and 1 Anonymous Users )




Powered by XOOPS 2.0 © 2001-2023 The XOOPS Project